Hidden leaks behind walls or under cabinets
We use thermal imaging and pin meters to find the leak and map the moisture. Then we open the wall as needed, dry the cavity, and repair the drywall so the problem is fixed, not just covered up.
When a pipe bursts or a supply line fails, Plumbing Leak Cleanup in Spanish Fork from our team stops the water, extracts what's pooled, and dries the structure before mold sets in. We handle emergency water removal for homeowners and businesses across Utah County, with same-day response and upfront pricing. Call now.

Plumbing Leak Cleanup in Spanish Fork is the process of stopping an active plumbing leak, removing the water it released, and drying the affected building materials so the damage doesn't spread. It covers everything from a pinhole supply-line leak under a kitchen sink to a burst pipe that soaks drywall, insulation, and subfloor. Our technicians locate the source, shut it down, extract standing water, and set drying equipment to pull moisture out of the structure. We also check for hidden moisture with thermal imaging and pin meters before we call the job done.
Spanish Fork homes face a few leak scenarios more than others. Older homes near the historic downtown area often have galvanized or early copper lines that corrode from the inside. Newer builds in the Palmyra and Salem areas can develop leaks at CPVC joints or where lines run through exterior walls that see hard freezes. A slow drip under a slab or behind a cabinet can run for weeks before you notice. By the time you see a water stain, the damage is usually bigger than it looks. That's why we treat every leak call as a moisture investigation, not just a mop-up.
Our Plumbing Leak Cleanup in Spanish Fork covers the full scope from leak source to dry structure. Here's what's included when you book with us.
We use thermal imaging and moisture meters to find the source and trace how far water traveled. This is included in every job so we're drying the right areas, not guessing.
We remove standing water from floors, carpet, and hard surfaces with truck-mounted and portable extractors. Extraction is included and typically takes 1 to 3 hours.
Air movers and dehumidifiers are included and sized for your space. We set them up, monitor daily, and adjust as needed until the structure is dry.
We check moisture readings every day and document them. You'll know exactly where things stand and when equipment can come out.
You get a completion report with photos, moisture logs, and a scope summary. This is what your adjuster needs to process a claim.
You call, we answer. We ask a few quick questions to understand the leak and dispatch a crew, typically within 60 to 90 minutes for emergency calls in Spanish Fork. We give you a clear arrival window and stay in touch if anything changes.
Our technician finds the source using thermal imaging and moisture meters, then shuts off the water if it's still running. We assess how far the water traveled and document affected materials with photos and readings. You get a clear scope and price before work begins.
We remove standing water with truck-mounted and portable extractors, including from carpet, pad, and hard surfaces. Extraction usually takes 1 to 3 hours depending on volume. We also pull water from wall cavities and under cabinets using specialty tools.
We set air movers and dehumidifiers to dry the structure, typically running 3 to 5 days. Each day we check moisture levels and adjust equipment. You'll see the readings and know exactly when the structure is dry.
We take final moisture readings and compare them to dry standards for the material type. Once everything is within range, we remove equipment and provide a completion report with photos and logs for your records or insurance claim.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Finds temperature differences caused by moisture behind walls and under floors. We use it to locate hidden leaks and map how far water traveled.
Measures moisture content in wood, drywall, and other materials. We use readings to set drying goals and confirm when materials are dry.
Pulls large volumes of water from carpet and hard surfaces fast. It's the first step in removing standing water after a leak.
Circulate air across wet surfaces to speed evaporation. We position them to dry walls, floors, and cavities evenly.
Remove moisture from the air so wet materials can dry. We size them for the space and run them alongside air movers.
Pull moisture out of hardwood floors without causing damage. We use them when water has soaked into wood flooring.
A supply line under the kitchen sink let go and water spread across the hardwood floor and into the cabinet base. The homeowner caught it within an hour, but water had already wicked into the toe kick and subfloor.
We extracted the water, set drying mats on the hardwood, and dried the cabinet base with air movers. Moisture readings dropped from 28% to 9% in four days. The hardwood and cabinets were saved.
A pipe in an exterior wall froze and burst during a cold snap. Water ran into the living room and soaked the carpet and pad. The homeowner shut off the water but didn't know how far it had spread.
We extracted water from the carpet, pulled the pad, and dried the subfloor. Thermal imaging showed moisture in the wall cavity, which we dried with directed airflow. Readings hit dry standard in five days.
The water heater failed and leaked across the basement floor, soaking carpet and stored boxes. Water had been running for a few hours before the homeowner noticed.
We removed the water, pulled back the carpet to dry the pad and concrete, and set dehumidifiers. The basement dried in three days. We documented everything for the insurance claim.
Leaks show up in different ways depending on the pipe, the fixture, and how long the water has been running. Here are the common problems we fix.
Ask a pro →We use thermal imaging and pin meters to find the leak and map the moisture. Then we open the wall as needed, dry the cavity, and repair the drywall so the problem is fixed, not just covered up.
We shut off the water, extract it fast, and dry the structure. Our crew handles burst pipe cleanup and can also help you identify vulnerable pipes so it doesn't happen again.
We extract the water, dry the area, and check for hidden moisture behind walls. We also help you document the damage for insurance and can recommend repair or replacement.
We find the source, dry the area thoroughly, and inspect for mold. If mold is present, we can handle remediation so your home is clean and dry again.
“A supply line under our kitchen sink let go on a Saturday morning. We called and had a crew at the house in about an hour. They extracted the water, set drying equipment, and checked moisture every day for four days. The cabinets and floor dried out without having to tear anything out. Price was what they quoted.”
Mark T.Homeowner, Palmyra
✓ Verified“Our water heater leaked in the basement and soaked the carpet and some boxes. The team was professional and explained everything. They pulled the carpet back, dried the pad and concrete, and set up dehumidifiers. They also helped with the insurance paperwork. I appreciated that they didn't try to sell me anything extra.”
Sandra L.Homeowner, Springville
✓ Verified“A pipe froze and burst in our exterior wall during a cold snap. Water ran into the living room and soaked the hardwood. The crew came out same day, extracted the water, and used drying mats on the floor. They saved the hardwood. I didn't think that was possible. Good communication the whole way through.”
Derek M.Homeowner, Salem
✓ VerifiedMost leak cleanup jobs in Spanish Fork run $500 to $2,500 depending on how much water spread and what materials are wet. A small under-sink leak that stayed contained might be on the low end, while a burst pipe that soaked drywall and flooring lands higher. We give you a written price before work starts, and we bill insurance directly when coverage applies.
Extraction usually takes 1 to 3 hours, and drying typically runs 3 to 5 days. The total depends on how much water was released and how many materials got wet. We check moisture daily and pull equipment as soon as readings hit dry standard, so you're not paying for extra days you don't need.
Box fans and open windows rarely dry a structure fully. Water hides in wall cavities, under flooring, and inside insulation where air can't reach. Without meters, you can't tell when it's actually dry. We use commercial dehumidifiers and air movers sized for the job, and we verify with readings so mold doesn't get a chance to start.
Most homeowner policies cover sudden and accidental water damage from a plumbing leak, like a burst pipe or failed supply line. Slow leaks that have been ongoing for months are often excluded. We document the source and damage so your adjuster can make a clear determination, and we can bill your carrier directly when the claim is approved.
Water spreads fast, and every hour counts. Call our Spanish Fork team for same-day emergency response, upfront pricing, and drying done to standard. We're available 24/7.
Call Now 343487650 →Call any time, day or night. We answer the phone around the clock and dispatch from Spanish Fork, so most addresses see us within 60 to 90 minutes. If you are not sure whether you need a full crew or just advice, call and we will tell you straight.